Warning: Creating default object from empty value in /homepages/11/d132647312/htdocs/Amfone/mkportal/include/SMF/smf_out.php on line 47
Inovonics 222 Wiring a D-104 to a Super Senior TX Question




 
The AM Forum
June 20, 2018, 03:25:18 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Calendar Links Staff List Gallery Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Inovonics 222 Wiring a D-104 to a Super Senior TX Question  (Read 281 times)
0 Members and 1 Guest are viewing this topic.
W6TOM
Contributing
Member
*
Offline Offline

Posts: 399


« on: June 05, 2018, 06:15:52 PM »

   I posted awhile back asking what might be a good peak limiter to use with my 80/40 Super Senior to avoid over modulation lockouts, the Inovonics 222 was one of the suggestions. I found one at a swap last weekend, now to wire it and do the adjustments.

    I have a D-104 with the K7DYY audio board and a 6 foot long microphone cord. The Inovonics 222 has a balanced input and output, op amps from the schematic.

    So what would be the best way to wire the D-104 to the input and also wire the output into the Super Senior?? Any suggestions on how I should set up the Inovonics 222?? Thanks!!!
Logged
w4bfs
W4 Beans For Supper
Contributing
Member
*
Offline Offline

Posts: 1220


more inpoot often yields more outpoot


« Reply #1 on: June 05, 2018, 06:39:11 PM »

without looking at a  222 manual, I think it works at line level, maybe selectable with jumpers, etc .... line level is roughly 2V pp into a 600 ohm load corresponding to 0 vu .... if you do not have a line level input on your tx then you should pad it down to avoid overdriving the mic preamp stages .... simplest way is a pot of any value from 600 ohm to meg ohms ....send the wiper to the mic audio tx connection .... maybe the d104/preamp will generate the 2Vpp needed, if not you will need some gain stage(s) ... scope time
Logged

Beefus

O would some power the gift give us
to see ourselves as others see us.
It would from many blunders free us.         Robert Burns
KQ6F
Member

Offline Offline

Posts: 55


« Reply #2 on: June 05, 2018, 07:27:52 PM »

I have same setup - Inovonics 222 into Super Sr.

Connect your amplified D-104 output to Input + and Gnd on 222.
Connect 222 Output + and Gnd to pin 2 and pin1, respectively on Super Sr front panel connector.
Logged
W6TOM
Contributing
Member
*
Offline Offline

Posts: 399


« Reply #3 on: June 08, 2018, 06:00:50 PM »

 Inputs are + _ and there are two common grounds, audio to + and _ or use common ground for audio ground?? Thanks....

Logged
KQ6F
Member

Offline Offline

Posts: 55


« Reply #4 on: June 08, 2018, 08:32:52 PM »

GNDs are both the same - doesn't matter.
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

AMfone - Dedicated to Amplitude Modulation on the Amateur Radio Bands
 AMfone 2001-2015
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Page created in 0.046 seconds with 18 queries.