The AM Forum
December 12, 2024, 05:54:12 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Calendar Links Staff List Gallery Login Register  
Pages: 1 2 [3]   Go Down
  Print  
Author Topic: What about QRO Plate Chokes??  (Read 43710 times)
0 Members and 1 Guest are viewing this topic.
KM1H
Contributing
Member
*
Offline Offline

Posts: 3514



« Reply #50 on: December 13, 2010, 08:18:17 PM »

Dont be surprised if you wind up using a vacuum relay to bypass L2 on the higher bands.
Logged
K1JJ
Contributing
Member
*
Offline Offline

Posts: 8886


"Let's go kayaking, Tommy!" - Yaz


« Reply #51 on: December 13, 2010, 08:27:42 PM »

Speaking of QRO plate chokes, does anyone recognize this one? It's not in the greatest shape but probably could be repaired with a little glue and tape. It has "9308" stamped on it.

Impressive looking, but I've tried a few of those in the early days for HF QRO and every one went off like a howlizer.. Grin Grin

I think the distributed capacitance or potential for multiple series resonace situations of those pie-wound rat nests is way too high for HF use. It's more suited as a BC/VLF choke device.

T
Logged

Use an "AM Courtesy Filter" to limit transmit audio bandwidth  +-4.5 KHz, +-6.0 KHz or +-8.0 KHz when needed.  Easily done in DSP.

Wise Words : "I'm as old as I've ever been... and I'm as young as I'll ever be."

There's nothing like an old dog.
N2ZD
Guest
« Reply #52 on: May 13, 2011, 11:20:17 PM »

I like the idea of using glass.

It would be easy enough to cut the ends off a Pyrex test tube from a scientific supply store...after two or three broken ones- LOL.

  Old thread revival, but here is some good info, cut the glass under water (carefully!!)
Logged
Opcom
Patrick J. / KD5OEI
Contributing
Member
*
Offline Offline

Posts: 8301



WWW
« Reply #53 on: May 14, 2011, 12:39:34 PM »

Glass would be the most elegant, but the Teflon is here. I do have to cut out L2 due to a resonance at 22 MHz of all places.

About glass, I was told to cut it with a hot wire, but that might not work well on Pyrex. Why is it better to cut glass under water?
Logged

Radio Candelstein
Opcom
Patrick J. / KD5OEI
Contributing
Member
*
Offline Offline

Posts: 8301



WWW
« Reply #54 on: May 14, 2011, 12:48:12 PM »

.
Logged

Radio Candelstein
KM1H
Contributing
Member
*
Offline Offline

Posts: 3514



« Reply #55 on: May 14, 2011, 03:42:04 PM »

Ive seen curved untempered auto glass cut with high pressure water and by sandblasting so anything is possible I guess.

Carl
Logged
W2VW
Contributing
Member
*
Offline Offline

Posts: 3483


WWW
« Reply #56 on: May 15, 2011, 10:36:49 AM »

This choke looks like the same type as the one used in the Harris AM-7224.

http://cgi.ebay.com/HARRIS-RF110A-High-power-RF-plate-choke-Assy-/150581415140?pt=LH_DefaultDomain_0&hash=item230f5a0ce4

It has a ferrite core which increases the inductance at low frequencies. The ferrite mix is doesn't do much at the higher frequencies. Less coil needed. Supposedly works from 1.6 to 30 megs without self resonances.
Logged
Pages: 1 2 [3]   Go Up
  Print  
 
Jump to:  

AMfone - Dedicated to Amplitude Modulation on the Amateur Radio Bands
 AMfone © 2001-2015
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Page created in 0.034 seconds with 19 queries.