The AM Forum
October 09, 2024, 08:53:21 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Calendar Links Staff List Gallery Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Hamwaves.com RF Inductance Calculator  (Read 11486 times)
0 Members and 1 Guest are viewing this topic.
aa5wg
Member

Online Online

Posts: 447


« on: January 27, 2010, 08:47:20 PM »

Hi to all

At the bottom of the RF Inductance Calculator located at Hamwaves.com  ( http://www.hamwaves.com/antennas/inductance.html ) Self-Resonant Frequency is listed.  The calculator states 1/4 (parallel) self resonant frequency of n=0 sheath helix mode. 

If I build/design a coil using this calculator and the listed self-resonant frequency is in the ham bands or close to the ham bands is this bad?

73,
Chuck
Logged
Opcom
Patrick J. / KD5OEI
Contributing
Member
*
Offline Offline

Posts: 8290



WWW
« Reply #1 on: January 27, 2010, 09:21:42 PM »


Wouldn't it be a good thing if it were self resonant at the operating frequency? That is a cool page.

What Z has the coil? In plinking, I'm not seeing near 50 ohms at a resonant frequency, but I don't know how to use the tool yet!


* weird_scientist.gif (2.41 KB, 64x71 - viewed 1296 times.)
Logged

Radio Candelstein
aa5wg
Member

Online Online

Posts: 447


« Reply #2 on: January 27, 2010, 09:37:15 PM »

I am building a tank coil for the link antenna coupler. i.e. One coil will be used on several band, 160 - 30 meters.  If there is a self resonance close or inside one of the bands is this bad?

73,
Chuck
Logged
Steve - WB3HUZ
Guest
« Reply #3 on: January 27, 2010, 10:02:43 PM »

Not necessarily bad but may cause tricky or touchy tuning.
Logged
Opcom
Patrick J. / KD5OEI
Contributing
Member
*
Offline Offline

Posts: 8290



WWW
« Reply #4 on: January 27, 2010, 11:55:16 PM »

I misunderstood what it was for.
Logged

Radio Candelstein
Steve - WB3HUZ
Guest
« Reply #5 on: January 28, 2010, 09:35:10 AM »

In most cases you would short out some turns on the coil as you move higher in frequency, so the self-resonance would also change and move higher.


I am building a tank coil for the link antenna coupler. i.e. One coil will be used on several band, 160 - 30 meters.  If there is a self resonance close or inside one of the bands is this bad?

73,
Chuck
Logged
aa5wg
Member

Online Online

Posts: 447


« Reply #6 on: January 28, 2010, 12:21:13 PM »

Is there a rule-of-thumb how far below self resonance I should operate the output tank coil.  This coil is for a link antenna coupler.
Both parallel and series feed will be used.
73,
Chuck
Logged
aa5wg
Member

Online Online

Posts: 447


« Reply #7 on: January 29, 2010, 10:28:39 PM »

Opcom, WB3HUZ:
Thank you.
Chuck
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

AMfone - Dedicated to Amplitude Modulation on the Amateur Radio Bands
 AMfone © 2001-2015
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Page created in 0.034 seconds with 19 queries.