The AM Forum
October 11, 2024, 11:12:32 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Calendar Links Staff List Gallery Login Register  
Pages: 1 ... 4 [5]   Go Down
  Print  
Author Topic: Analog modulating a 1000 watt carrier class E rig  (Read 90337 times)
0 Members and 1 Guest are viewing this topic.
ka1tdq
Member

Offline Offline

Posts: 1506


Red part turned in for a refund.


« Reply #100 on: September 28, 2019, 01:48:48 PM »

It's funny but I'm almost a step ahead of you. I already have the bucket and it'd be easy just to add salt water!

Actually, I was using the bucket was for secondary containment.

I stopped at HRO this morning and got 100' of LMR400. I'll install it tomorrow. My kid's birthday party today.

Jon


* IMG_1605.jpg (2134.08 KB, 4032x3024 - viewed 869 times.)
Logged

It’s not just values, it’s business.
ka1tdq
Member

Offline Offline

Posts: 1506


Red part turned in for a refund.


« Reply #101 on: September 28, 2019, 07:31:07 PM »

...and I let the smoke out. I'm not sure of exactly what, but it looks like one of the drivers. I'm thinking the problem all along was parasitics.

I replaced my antenna feed line with a near perfect SWR, tuned up at 300 watts with a nice safe waveform, unkeyed... When I keyed up again the waveforms were completely scattered with smoke coming from something.

I'm thinking I should've put those 300 ohm resistors inline with each driver.

Jon
Logged

It’s not just values, it’s business.
w8khk
Member

Online Online

Posts: 1211


This ham got his ticket the old fashioned way.


WWW
« Reply #102 on: September 29, 2019, 01:36:41 AM »

You might want to consider adding one of these:

http://www.classeradio.com/efficiency_meter_rev_f.pdf
Logged

Rick / W8KHK  ex WB2HKX, WB4GNR
"Both politicians and diapers need to be changed often and for the same reason.”   Ronald Reagan

My smart?phone voicetext screws up homophones, but they are crystal clear from my 75 meter plate-modulated AM transmitter
ka1tdq
Member

Offline Offline

Posts: 1506


Red part turned in for a refund.


« Reply #103 on: September 29, 2019, 10:13:12 AM »

The 5-meter method does just as well.

At some point I'll pull the heat sink assembly, replace the damaged components and put in some parasitic suppression.

Jon
Logged

It’s not just values, it’s business.
w8khk
Member

Online Online

Posts: 1211


This ham got his ticket the old fashioned way.


WWW
« Reply #104 on: September 29, 2019, 10:37:32 AM »

The 5-meter method does just as well.

The idea here is that the QIX board monitors AND SHUTS DOWN immediately upon overload.  No human can respond to an overload that quickly while monitoring meters visually.  The alternative: ordering from Mouser or Digi-key and soldering OFTEN.  Certainly worth a careful look at this option.
Logged

Rick / W8KHK  ex WB2HKX, WB4GNR
"Both politicians and diapers need to be changed often and for the same reason.”   Ronald Reagan

My smart?phone voicetext screws up homophones, but they are crystal clear from my 75 meter plate-modulated AM transmitter
ka1tdq
Member

Offline Offline

Posts: 1506


Red part turned in for a refund.


« Reply #105 on: September 29, 2019, 11:34:28 AM »

Oh
Logged

It’s not just values, it’s business.
Opcom
Patrick J. / KD5OEI
Contributing
Member
*
Offline Offline

Posts: 8290



WWW
« Reply #106 on: October 02, 2019, 12:43:46 AM »

Ugh! Oily cantennas!! You'd think Heathkit could have offered something with a bellows.
Logged

Radio Candelstein
steve_qix
Contributing
Member
*
Offline Offline

Posts: 2595


Bap!


WWW
« Reply #107 on: October 02, 2019, 10:46:35 PM »


I'm thinking I should've put those 300 ohm resistors inline with each driver.

Jon

Yes, those resistors have to be there, or the likelyhood of parasitics is quite high.

Logged

High Power, Broadcast Audio and Low Cost?  Check out the class E web site at: http://www.classeradio.org
ka1tdq
Member

Offline Offline

Posts: 1506


Red part turned in for a refund.


« Reply #108 on: October 03, 2019, 09:49:29 AM »

It'll require a rebuild of the heat sink assembly.

Something to note, the transzorbs protected two of four mosfet modules. Once I cut out the transzorbs, the dead short went away from the drain bus for those two modules. Something else went as well with the remaining two modules.

After all this, I still had a sporadically fluctuating SWR problem when using my rice box. I had a coax splice in the shack that was intermittently making connection. I could shake the coax at the splice and SWR would jump all over the place. Once I put a new connector on, the problem went away. I'm sure this contributed to the parasitic problem as well.

It's a shame though to blow up a rig over a PL-259.

Jon
Logged

It’s not just values, it’s business.
ka1tdq
Member

Offline Offline

Posts: 1506


Red part turned in for a refund.


« Reply #109 on: October 03, 2019, 07:45:50 PM »

Actually I take that back. I forgot that I installed two transzorbs per mosfet module. Once I cut them all out and did resistance checks, I realized that the drains were protected. So, all seems ok and I'll just need to solder on more transzorbs.

But, in the time since I thought I blew up my class E rig, I converted my 75 meter dipole into a 40 meter delta loop and bought an Icom 7300. What a nice rig!

Jon


* IMG_1671.jpg (2813.54 KB, 4032x3024 - viewed 974 times.)
Logged

It’s not just values, it’s business.
ka1tdq
Member

Offline Offline

Posts: 1506


Red part turned in for a refund.


« Reply #110 on: November 01, 2019, 02:44:33 PM »

I figured out a way to solder new Transzorbs in place without disassembling the heat sink. I have ground connections on either side of the heat sink. I can just pre-solder the ground side of the Transzorbs onto a solid piece of #12 wire, in the correct positions, and slide it in place over the drain buses. The wire would be connected to the grounds on either side and then I'd just need to solder the other end of the Tranzorbs onto the drain buses.

The problem was that the area between the heat sink and transformer assemblies is tight, without much room to sneak a soldering iron in.

Once I do this, I can resume testing.

I needed some new inspiration.

Jon



* IMG_1746.jpg (1709.47 KB, 3725x2794 - viewed 1009 times.)

* IMG_1730.jpg (2218.24 KB, 4032x3024 - viewed 1075 times.)
Logged

It’s not just values, it’s business.
Pages: 1 ... 4 [5]   Go Up
  Print  
 
Jump to:  

AMfone - Dedicated to Amplitude Modulation on the Amateur Radio Bands
 AMfone © 2001-2015
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Page created in 0.052 seconds with 19 queries.