The AM Forum
May 14, 2024, 01:36:24 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Calendar Links Staff List Gallery Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: EICO 720 filter & power replace  (Read 2218 times)
0 Members and 1 Guest are viewing this topic.
w1vtp
Member

Offline Offline

Posts: 2632



« on: March 17, 2012, 11:14:43 PM »

Tho't I'd share my experience with replacing a transformer in one of my 3 EICO 720s and my PS filter caps replacement

The transformer and 720 were two separate eBay purchases.  I determined the different windings by apply 1 volt @ 60~ from a function oscillator to the two black wires of the primary. This was necessary because all the other windings (except for the green wire) had faded to a light brown.  So with the 1 volt applied, the secondary was 12 volts (for the 1200 volt secondary), the center tap was 6 volts (for the 600 volts) and so on. A much safer approach than using a Variac or plugging directly into 110 volts.

The filter caps need to be replaced without exception. I don't know what the source of caps were that EICO used but all three of my 720s needed to have them replaced.  I tried to get away without doing this with one 720 and was completely fogged out in the workshop with some sort of vile white cloud.  Fortunately, I have a good vent fan and was able to clear out the fog of unknown chemical substance but I learned my lesson.  The first pic shows 720 #2 & #3 just after the transformer installation and before the cap replacement.  The second pic shows #3 with more detail of my filter replacement, just before tie wrapping the transformer leads.  I settled on a certain terminal strip that used an already present screw and epoxied the other end of the strip the the chassis -- no drilling and blasting.

The above chassis pic shows the replacement power transformer in place

Al


* 720 2&3.jpg (284.92 KB, 2000x1032 - viewed 374 times.)

* PS FILTER CAP UPGRADE sm.jpg (1185.54 KB, 4928x3264 - viewed 485 times.)

* Back with driver cover.jpg (240.34 KB, 2000x1325 - viewed 400 times.)
Logged
WB4AQL
Member

Offline Offline

Posts: 54


« Reply #1 on: March 18, 2012, 02:44:54 PM »

Very nice! Al, how did you select that transformer for purchase in the first place? Wasn`t it an unknown quantity?

Mike  WB4AQL
Logged
w1vtp
Member

Offline Offline

Posts: 2632



« Reply #2 on: March 18, 2012, 05:43:36 PM »

Very nice! Al, how did you select that transformer for purchase in the first place? Wasn`t it an unknown quantity?

Mike  WB4AQL


Mike - it's an exact replacement for the 720.  I have an ongoing saved search on eBay for the EICO 720 (and 730) so I got an automatic email alerting me to the transformer which gave me the opportunity to purchase it.  That's how I "operate" - I buy stuff "just in case" and many times this has allowed me to do these sort of exercises.  The downside of this approach is that I need lots of storage space and then I need to know where I squirreled the stuff away.  Grin

Al
Logged
WB4AQL
Member

Offline Offline

Posts: 54


« Reply #3 on: March 18, 2012, 06:55:03 PM »

Smooth! Very smooth!

Mike
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

AMfone - Dedicated to Amplitude Modulation on the Amateur Radio Bands
 AMfone © 2001-2015
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Page created in 0.079 seconds with 19 queries.