The AM Forum
March 28, 2024, 04:03:18 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Calendar Links Staff List Gallery Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Collins 51J2  (Read 2644 times)
0 Members and 1 Guest are viewing this topic.
n1ps
Contributing
Member
*
Offline Offline

Posts: 338


websdr http://sebagolakesdr.us:8901/


« on: August 02, 2021, 09:31:05 AM »

I figure some on here are familiar with this receiver.  It has an odd issue.  Above the BC band, it receivers 1MHZ higher than what is dialed up.  For example, on band 2, setting dial to 1.9 MHz, it actually receivers on 2.9.  On band 4, with dial set to 3.9, it receivers on 4.9, etc on up.  Band 3 is dead and may be another issue.  The BC band is correct.  At the moment I would like to figure out the wrong band issue first.  Possible a bandswitch issue being set wrong (like someone removed it and set it back one position off)?

TNX
Peter



Logged
WBear2GCR
Member

Offline Offline

Posts: 4135


Brrrr- it's cold in the shack! Fire up the BIG RIG


WWW
« Reply #1 on: August 02, 2021, 01:55:09 PM »

First carefully check to see that the xtals for the xtal osc are installed in the proper sockets, sounds like they are NOT?

Then you can double check with a freq counter and see that the correct freq is being picked for each band.
Or a scope and do the conversion from time to freq...

                            _-_-
Logged

_-_- bear WB2GCR                   http://www.bearlabs.com
n1ps
Contributing
Member
*
Offline Offline

Posts: 338


websdr http://sebagolakesdr.us:8901/


« Reply #2 on: August 02, 2021, 03:24:10 PM »

update:  Turns out the bandswitch drum is out of alignment by abt 1/2 of a position.  The actual problem is the even bands are dead at least on the lower bands.   It may be the crystal switch is not synched correctly with the BSW.  More work to be done on this.  I am pretty unfamiliar with this set...but getting more familiar with it as I go through it! 
Logged
n1ps
Contributing
Member
*
Offline Offline

Posts: 338


websdr http://sebagolakesdr.us:8901/


« Reply #3 on: August 02, 2021, 04:47:35 PM »

All good.  Everything was badly out of alignment. 
Logged
WBear2GCR
Member

Offline Offline

Posts: 4135


Brrrr- it's cold in the shack! Fire up the BIG RIG


WWW
« Reply #4 on: August 02, 2021, 05:26:42 PM »

way to go!

post pic?
Logged

_-_- bear WB2GCR                   http://www.bearlabs.com
n1ps
Contributing
Member
*
Offline Offline

Posts: 338


websdr http://sebagolakesdr.us:8901/


« Reply #5 on: August 03, 2021, 04:26:19 PM »

Will do when complete.  Not out of the woods quite yet.  The even bands are abt 6-8db worse than the odd for senselesstivity.  There are a couple adjustments for this associated with the IF switch shaft, but that did not fix the imbalance.  It doesnt help that the print I have is poor and I gather there are several errors on it from reading around the web.   
Logged
n1ps
Contributing
Member
*
Offline Offline

Posts: 338


websdr http://sebagolakesdr.us:8901/


« Reply #6 on: August 13, 2021, 08:44:55 PM »

Finished up the 51J a few days ago.  The pic shows the repair for a couple loose IF coils.  One had a broken wire for the even bands.  Started it several months ago...works well now on all bands.  Impressive engineering.  It belongs to my son in law Jay.  He will enjoy this one.


* 51J.JPG (508.37 KB, 1296x968 - viewed 221 times.)
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

AMfone - Dedicated to Amplitude Modulation on the Amateur Radio Bands
 AMfone © 2001-2015
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Page created in 0.033 seconds with 19 queries.